Oscilloscope Probes

An oscilloscope is considered to be the most used instrument for electrical engineers who need to measure electrical characteristics of electronic devices but you also need at least one probe.Things to consider when choosing probes Ensure the probe's input connector matches the connector on your scope Choose a probe whose input resistance and capacitance match the input resistance and capacitance of your scope - matching is critical for guaranteeing proper signal transfer and signal accuracyThe best approach, for matching a probe with a scope, is to first choose a probe whose capacitance is within the range of your scope and then fine-tune the probe's capacitance by adjusting its compensation network using the probe's trimmer capacitor. The 1X probes are suitable for many low frequency applications. They typically offer the same input impedance of the oscilloscope which is normally 1 M Ohm. The most common type of probe with a built in attenuator gives an attenuation of ten, and it is known as a 10X oscilloscope probeTypes of probesPassive probes are the most commonly used probes for taking measurements. They are easy to use, relatively inexpensive, and fairly rugged. Available in the following configurations: 1´: no attenuation 10´: factor-of-10 attenuation 100´: factor-of-100 attenuation 1000´: factor-of-1000 attenuationAttenuation probes serve to multiply the voltage measurement range of the oscilloscope by using an internal resistor that, when used in conjunction with the input resistance of the scope, creates a voltage divider. Useful for the following reasons: It allows for the measurement of a signal that might exceed the limits of the oscilloscope. The attenuation circuitry results in higher resistance and lower capacitance, which is important for high-frequency measurements.Active probes contain active components, such as FETs or amplifiers. Commonly used for taking high-speed measurements (>500 MHz) or on high-impedance circuits. One limitation is their limited voltage range. Differential probes are popular for measuring high-frequency signals or signals of very low amplitude.A current probe measures the electrical current flowing through a conductor. Tips Always use an appropriate probe tip and/or probe tip adapter whenever possible Keep ground leads short

...
Read more Read less

Filter

Visar 21 - 40 av 197 produkter
Resultat per sida
Beskrivning Pris Probe Type Attenuation Bandwidth Maximum Common Mode Input Voltage Connector Type Model Number p Number of Probes Safety Category Level Safety Category Voltage Series Safety Category Rise Time
RS-artikelnummer 715-8743
Tillv. art.nrTPP0201-PK10
VarumärkeTektronix
610,79 kr
Each (In a Pack of 10)
Enheter
Passive 1:10 200MHz 300V BNC TPP0201 - CAT I, CAT II 300 V, 300 V ac, 400 V ac TPP CAT I 400 V ac, CAT II 300 V, CAT II 300 V ac 2.3ns
RS-artikelnummer 801-4880
Tillv. art.nrPP066
VarumärkeTeledyne LeCroy
16 373,12 kr
Each
Enheter
Passive 1:10, 1:20 7.5GHz 15V BNC, SMA PP066 - - - - - 47ps
RS-artikelnummer 518-0993
Tillv. art.nr99.00224
VarumärkeStaubli
469,56 kr
Pr. Set
Sats(er)
Passive 1:10 150MHz - BNC 99.00224 - CAT II 1000V - CAT II 1000 V 1.2ns
RS-artikelnummer 123-6478
VarumärkeRS PRO
4 233,18 kr
Each
Enheter
Differential, High Voltage 1:10, 1:100 50MHz 1.5kV - - 1 - - - - -
RS-artikelnummer 898-6788
Tillv. art.nrTA112
VarumärkePico Technology
8 848,77 kr
Each
Enheter
Active 1:10 1GHz 33V BNC - 2 - 20V - - -
RS-artikelnummer 668-7161
Tillv. art.nrTDP1500
VarumärkeTektronix
49 234,00 kr
Each
Enheter
Active, Differential 1:1, 1:10 1.5GHz 25V - TDP1500 - - - TDP - 265ps
RS-artikelnummer 661-3295
Tillv. art.nrP6316
VarumärkeTektronix
6 684,70 kr
Each
Enheter
Logic, Passive - - - - P6316 - - - - - -
RS-artikelnummer 715-8733
Tillv. art.nrTPP0101
VarumärkeTektronix
566,50 kr
Each
Enheter
Passive, Voltage 1:10 100MHz 300V BNC TPP0101 - CAT I, CAT II 300 V, 300 V ac, 400 V ac TPP CAT I 400 V ac, CAT II 300 V, CAT II 300 V ac 3.5ns
RS-artikelnummer 773-3574
Tillv. art.nrVPS510-B
VarumärkeFluke
1 929,00 kr
Each
Enheter
Passive 1:10 500MHz - BNC VPS510 1 CAT III 300V 190 II CAT III 300V 0.7ns
RS-artikelnummer 512-6078
Tillv. art.nrTT-SI 9010
VarumärkeTestec
7 790,00 kr
Each
Enheter
Active, Differential 1:100, 1:1000 70MHz 5kV BNC TT-SI 9010 - CAT I, CAT II 2500 V ac, 7000 V ac/dc SI CAT I 2500 V ac, CAT II 7000 V ac/dc 5ns
RS-artikelnummer 734-5013
Tillv. art.nrP5100A
VarumärkeTektronix
5 665,00 kr
Each
Enheter
Passive 1:100 500MHz 1kV - P5100A - CAT II 1000V ac 5000 CAT II 1000 V ac 700ps
RS-artikelnummer 672-1706
Tillv. art.nrZS1000
VarumärkeTeledyne LeCroy
12 220,00 kr
Each
Enheter
Active 1:10 1GHz - ProBus ZS1000 - - - ZS - -
RS-artikelnummer 797-3390
Tillv. art.nrTPP0500B
VarumärkeTektronix
6 643,50 kr
Each
Enheter
Passive 1:10 500MHz 300V Hook Clip TPP0500B 1 CAT II 300V TPP0 CAT II 300 V -
RS-artikelnummer 518-0971
Tillv. art.nr99.00170
VarumärkeStaubli
620,99 kr
Pr. Set
Sats(er)
Passive 1:10 450MHz - BNC 99.00170 - CAT II, CAT III 600 V, 1000 V - CAT II 1000 V, CAT III 600 V 1ns
RS-artikelnummer 878-7610
Tillv. art.nrZS1500
VarumärkeTeledyne LeCroy
24 225,00 kr
Each
Enheter
Active 1:10 1.5GHz - ProBus ZS1500 2 - - ZS - -
RS-artikelnummer 715-8746
Tillv. art.nrTPP0101-PK10
VarumärkeTektronix
507,79 kr
Each (In a Pack of 10)
Enheter
Passive 1:10 100MHz 300V BNC TPP0101 - CAT I, CAT II 300 V, 300 V ac, 400 V ac TPP CAT I 400 V ac, CAT II 300 V, CAT II 300 V ac 3.5ns
RS-artikelnummer 725-6604
Tillv. art.nrP6139B
VarumärkeTektronix
5 397,20 kr
Each
Enheter
Passive 1:10 500MHz - BNC P6139B - CAT II 300V - CAT II 300 V -
RS-artikelnummer 733-6139
Tillv. art.nrN2795A
11 191,00 kr
Each
Enheter
Active 1:10 1GHz - - N2795A - - - N - 350ps
RS-artikelnummer 661-3292
Tillv. art.nrTDP0500
VarumärkeTektronix
41 406,00 kr
Each
Enheter
Differential, High Voltage 1:5, 1:50 500MHz 30V - TDP0500 - - - TDP - 700ps
RS-artikelnummer 728-6759
Tillv. art.nrTPP1000
VarumärkeTektronix
11 124,00 kr
Each
Enheter
Passive 1:10 1GHz 300V - TPP1000 - CAT II 300V 4000, 5000 CAT II 300 V -
Related Products
The i30 may be used in conjunction with ...
Description:
The i30 may be used in conjunction with bench and portable oscilloscopes for accurate non-intrusive ac & dc current measurement.,Applications include: inverters, switch mode power supplies, industrial controllers, automotive leakage currents and other applications requiring accurate isolated current measurement. ...
For measurement of flux density and magnetic field ...
Description:
For measurement of flux density and magnetic field strength of DC,AC and peak magnetic fields in S.I c.g.s units, these two micropressor-controlled menu-driven instruments are the GM07 & GM08 series. Featuring graphical monochrome LCD display, probe polarity inidicator and operating ...
MDO3000 oscilloscopes are designed to meet users' needs ...
Description:
MDO3000 oscilloscopes are designed to meet users' needs and aspirations now and into the future. Each model is multi-functional with integrated basic spectrum analyzer, Wave Inspector Navigation, MSO, serial and parallel bus triggering and analysis, and digital voltmeter. Optional instrument ...
Tektronix MSO/DPO2000 accessories include: analysis modules embedded serial ...
Description:
Tektronix MSO/DPO2000 accessories include: analysis modules embedded serial triggering DPO2EMBD ( 575-614 ), computer serial triggering DPO2COMP ( 575-563 ) and automotive serial triggering DPO2AUTO ( 575-573 ); video out port DPO2CONN ( 575-579 ); soft carrying case ACD2000 ( ...