Oscilloscope Probes

An oscilloscope is considered to be the most used instrument for electrical engineers who need to measure electrical characteristics of electronic devices but you also need at least one probe.Things to consider when choosing probes Ensure the probe's input connector matches the connector on your scope Choose a probe whose input resistance and capacitance match the input resistance and capacitance of your scope - matching is critical for guaranteeing proper signal transfer and signal accuracyThe best approach, for matching a probe with a scope, is to first choose a probe whose capacitance is within the range of your scope and then fine-tune the probe's capacitance by adjusting its compensation network using the probe's trimmer capacitor. The 1X probes are suitable for many low frequency applications. They typically offer the same input impedance of the oscilloscope which is normally 1 M Ohm. The most common type of probe with a built in attenuator gives an attenuation of ten, and it is known as a 10X oscilloscope probeTypes of probesPassive probes are the most commonly used probes for taking measurements. They are easy to use, relatively inexpensive, and fairly rugged. Available in the following configurations: 1´: no attenuation 10´: factor-of-10 attenuation 100´: factor-of-100 attenuation 1000´: factor-of-1000 attenuationAttenuation probes serve to multiply the voltage measurement range of the oscilloscope by using an internal resistor that, when used in conjunction with the input resistance of the scope, creates a voltage divider. Useful for the following reasons: It allows for the measurement of a signal that might exceed the limits of the oscilloscope. The attenuation circuitry results in higher resistance and lower capacitance, which is important for high-frequency measurements.Active probes contain active components, such as FETs or amplifiers. Commonly used for taking high-speed measurements (>500 MHz) or on high-impedance circuits. One limitation is their limited voltage range. Differential probes are popular for measuring high-frequency signals or signals of very low amplitude.A current probe measures the electrical current flowing through a conductor. Tips Always use an appropriate probe tip and/or probe tip adapter whenever possible Keep ground leads short

...
Read more Read less

Filter

Visar 61 - 80 av 197 produkter
Resultat per sida
Beskrivning Pris Probe Type Attenuation Bandwidth Maximum Common Mode Input Voltage Connector Type Model Number p Number of Probes Safety Category Level Safety Category Voltage Series Safety Category Rise Time
RS-artikelnummer 898-6753
Tillv. art.nrTA045
VarumärkePico Technology
9 192,26 kr
Each
Enheter
Active, Differential 1:10 200MHz 60V - - 2 CAT I ±60V - CAT I ±60V -
RS-artikelnummer 747-1862
Tillv. art.nrTHP0301-Y
VarumärkeTektronix
2 111,50 kr
Each
Enheter
Passive 1:10 300MHz - BNC THP0301-Y - CAT III 300V THP CAT III 300 V -
RS-artikelnummer 137-2359
Tillv. art.nrVPS410-II-B
VarumärkeFluke
2 267,56 kr
Each
Enheter
Passive 1:10 500MHz - - VPS410-II-B - CAT III, CAT IV 600 V, 1000 V VPS410 CAT III 1000 V, CAT IV 600 V -
RS-artikelnummer 922-5270
Tillv. art.nrPP026-1
VarumärkeTeledyne LeCroy
4 055,00 kr
Each
Enheter
Passive 1:10 500MHz - BNC PP026 1 CAT I, CAT II 400 Vrms, 500 Vrms - CAT I 500 Vrms, CAT II 400 Vrms 700ps
RS-artikelnummer 825-1212
Tillv. art.nr68.9433-28
VarumärkeStaubli
770,63 kr
Pr. Set
Sats(er)
Passive 1:10 500MHz - BNC 68.9433-28 1 CAT III 300V SET Isoprobe CAT III 300 V -
RS-artikelnummer 174-8877
Tillv. art.nrPP017-1
VarumärkeTeledyne LeCroy
1 895,63 kr
Each
Enheter
Passive 1:10 250MHz 1.5kV - - 1 CAT II - PP017 CAT II 300 Vrms 1.4ns
RS-artikelnummer 174-9604
Tillv. art.nrTA386
VarumärkePico Technology
341,22 kr
Each
Enheter
Passive 1:1, 1:10 200MHz - Hook Clip TA386 1 - - - - 35ns
RS-artikelnummer 512-5003
Tillv. art.nrMX9030-Z
VarumärkeMetrix
3 384,00 kr
Each
Enheter
Differential, Gripper 1:1, 1:20, 1:200 30MHz - - MX 9030-Z 5 CAT IV 600V - CAT IV 600 V 11.7ns
RS-artikelnummer 146-5604
Tillv. art.nr460-004
VarumärkeDigilent
189,84 kr
Each
Enheter
Passive 1:10 6MHz - BNC - 2 - - - - -
RS-artikelnummer 898-6832
Tillv. art.nrTA061
VarumärkePico Technology
2 942,56 kr
Each
Enheter
Passive 1:10 1.5GHz 12V SMA - 1 - 12V - - 240ps
RS-artikelnummer 878-7617
Tillv. art.nrZD1500
VarumärkeTeledyne LeCroy
68 350,00 kr
Each
Enheter
Active, Differential 1:1 1.7GHz 10V ProBus ZD1500 2 - - ZD - 270ps
RS-artikelnummer 177-1275
Tillv. art.nrT3PP300
VarumärkeTeledyne LeCroy
885,00 kr
Each
Enheter
Passive 1:1, 1:10 300MHz - - - - - - T3DSO - -
RS-artikelnummer 898-6747
Tillv. art.nrTA042
VarumärkePico Technology
5 366,46 kr
Each
Enheter
Active, Differential 1:100, 1:1000 100MHz 1kV - - 2 CAT III 1000 Vrms, 1400 V ac/dc - CAT III 1400 V ac/dc, 1000 Vrms 3.5ns
RS-artikelnummer 146-6623
VarumärkeRS PRO
470,26 kr
Each
Enheter
Passive 1:100 300MHz 700V BNC - 1 CAT I 2500V - CAT I 2500 V 1.2ns
RS-artikelnummer 174-8872
Tillv. art.nrHVD3206A-6M
VarumärkeTeledyne LeCroy
30 660,00 kr
Each
Enheter
Differential 1:50, 1:500 80MHz 1kV - - 1 CAT I, CAT III 1000 Vrms, 1500 V dc, 2000 V HVD3000A CAT I 2000 V, CAT III 1000 Vrms, CAT III 1500 V dc 4.4ns
RS-artikelnummer 724-0933
Tillv. art.nrPP008-1
VarumärkeTeledyne LeCroy
4 110,00 kr
Each
Enheter
Passive 1:10 500MHz 400V BNC PP008-1 - CAT I, CAT II 300 V ac, 400 V ac PP CAT I 400 V ac, CAT II 300 V ac -
RS-artikelnummer 898-6781
Tillv. art.nrTA222
VarumärkePico Technology
10 219,85 kr
Each
Enheter
Active 1:10 1.5GHz 20V BNC, SMA adapter - 2 - 20V - - -
RS-artikelnummer 668-7167
Tillv. art.nrTDP1000
VarumärkeTektronix
46 865,00 kr
Each
Enheter
Differential, High Voltage 1:5, 1:50 1GHz 30V - TDP1000 - - - TDP - 350ps
RS-artikelnummer 922-5261
Tillv. art.nrPP024-2
VarumärkeTeledyne LeCroy
6 363,19 kr
Each
Enheter
Passive 1:10 500MHz - BNC PP024 1 CAT I, CAT II 400 Vrms, 500 Vrms - CAT I 500 Vrms, CAT II 400 Vrms 700ps
RS-artikelnummer 863-3746
Tillv. art.nrZS2500
VarumärkeTeledyne LeCroy
30 116,61 kr
Each
Enheter
Active 1:10 2.5GHz 20V ProBus ZS2500 1 - - ZS - -
Related Products
The i30 may be used in conjunction with ...
Description:
The i30 may be used in conjunction with bench and portable oscilloscopes for accurate non-intrusive ac & dc current measurement.,Applications include: inverters, switch mode power supplies, industrial controllers, automotive leakage currents and other applications requiring accurate isolated current measurement. ...
For measurement of flux density and magnetic field ...
Description:
For measurement of flux density and magnetic field strength of DC,AC and peak magnetic fields in S.I c.g.s units, these two micropressor-controlled menu-driven instruments are the GM07 & GM08 series. Featuring graphical monochrome LCD display, probe polarity inidicator and operating ...
MDO3000 oscilloscopes are designed to meet users' needs ...
Description:
MDO3000 oscilloscopes are designed to meet users' needs and aspirations now and into the future. Each model is multi-functional with integrated basic spectrum analyzer, Wave Inspector Navigation, MSO, serial and parallel bus triggering and analysis, and digital voltmeter. Optional instrument ...
Tektronix MSO/DPO2000 accessories include: analysis modules embedded serial ...
Description:
Tektronix MSO/DPO2000 accessories include: analysis modules embedded serial triggering DPO2EMBD ( 575-614 ), computer serial triggering DPO2COMP ( 575-563 ) and automotive serial triggering DPO2AUTO ( 575-573 ); video out port DPO2CONN ( 575-579 ); soft carrying case ACD2000 ( ...