Tektronix Oscilloscopmodul Differentiell förförstärkare, till TDS400 Series, TDS500 Series, TDS5000 Series, TDS600

Se alla Oscilloskopmoduler

Antal (1 enhet)*

42 884,60 kr

(exkl. moms)

53 605,75 kr

(inkl. moms)

Add to Basket
välj eller skriv kvantitet
I lager
  • Dessutom levereras 1 enhet(er) från den 25 maj 2026
Behöver du mer? Ange den kvantitet du behöver och klicka på "Kontrollera leveransdatum"
Enheter
Per enhet
1 +42 884,60 kr

*vägledande pris

RS-artikelnummer:
349-8214
Tillv. art.nr:
ADA400A
Tillverkare / varumärke:
Tektronix
Hitta liknande produkter genom att välja ett eller flera attribut.
Välj alla

Varumärke

Tektronix

Modultyp

Differentiell förförstärkare

Produkttyp

Oscilloscopmodul

För användning med

TDS400 Series, TDS500 Series, TDS5000 Series, TDS600 Series, TDS700 Series, TDS7000 Series

Modellnummer

ADA400A

Standarder/godkännanden

CE, ISO 14001, ISO 9001

RoHS-status: Undantagen

COO (ursprungsland):
US

Tektronix ADA400A 1 MHz Differential Preamplifier


10μV/div Sensitivity

Low Pass filters for 100Hz, 3kHz, 100Hz and Full (1 MHz)

Typically 100 dB CMRR DC to 10 kHz

Selectable Gain: 100, 10, 1 or 0.1

Accurately measures signal as small as 5uV

Integral Probe Power with TEKPROBE ™ BNC

The ADA400A Active Differential Preamplifier allows direct oscilloscope measurements of very low amplitude voltages and signals which are not ground referenced. The high impedance of both inputs eliminates the need to add additional ground points in the DUT, thereby avoiding circulating currents which disturb the measurement or the circuit.

The high gain and extremely high common mode rejection provide usable measurements of voltages as low as 5μV, even in high noise environments. Selectable bandwidth limiting reduces normal mode noise from digital logic, switch mode power supplies and line frequency sources. Adjustable differential offset allows the user to null out transducer bridge bias and galvanic potential from the test set-up. An "infinite impedance" mode can be selected in the two highest gain ranges allowing accurate measurements of signals with high source impedance. It is specifically designed to operate on Tektronix oscilloscopes with TEKPROBE® interface.

Tektronix ADA400A 1 MHz Differential Preamplifier


The ADA400A Active Differential Preamplifier allows direct oscilloscope measurements of very low amplitude voltages and signals which are not ground referenced. The high impedance of both inputs eliminates the need to add additional ground points in the DUT, thereby avoiding circulating currents which disturb the measurement or the circuit.,The high gain and extremely high common mode rejection provide usable measurements of voltages as low as 5μV, even in high noise environments. Selectable bandwidth limiting reduces normal mode noise from digital logic, switch mode power supplies and line frequency sources. Adjustable differential offset allows the user to null out transducer bridge bias and galvanic potential from the test set-up. An "infinite impedance" mode can be selected in the two highest gain ranges allowing accurate measurements of signals with high source impedance. It is specifically designed to operate on Tektronix oscilloscopes with TEKPROBE® interface

10μV/div Sensitivity

Low-pass filter: 100Hz, 3kHz, 100Hz or Full (1 MHz)

Typically 100 dB CMRR DC to 10 kHz

Selectable Gain: 100, 10, 1 or 0.1

Accurately measures signal as small as 5uV

Integral Probe Power with TEKPROBE™BNC

Relaterade länkar