Microchip , 1-Channel Ethernet Transceiver 48-Pin QFN, KSZ9031RNXCC
- RS-artikelnummer:
- 177-3847
- Tillv. art.nr:
- KSZ9031RNXCC
- Tillverkare / varumärke:
- Microchip
1290 I lager för avsändande samma dag
Lagt till varukorgen
Pris (ex. moms) Var (i ett paket med 5)
36,02 kr
(exkl. moms)
45,02 kr
(inkl. moms)
| Enheter | Per unit | Per Pack* |
| 5 + | 36,02 kr | 180,10 kr |
- RS-artikelnummer:
- 177-3847
- Tillv. art.nr:
- KSZ9031RNXCC
- Tillverkare / varumärke:
- Microchip
Datablad
Lagstiftning och ursprungsland
- COO (Country of Origin):
- TW
Produktdetaljer
The KSZ9031 reduces board cost and simplifies board layout by using on-chip termination resistors for the four differential pairs and by integrating an LDO controller to drive a low-cost MOSFET to supply the 1.2V core.
Single-chip 10/100/1000Mbps Ethernet transceiver
KSZ9031Mxx feature GMII/MII standard interface with 3.3V/2.5V/1.8V tolerant I/Os
KSZ9031Rxx feature RGMII timing supports on-chip delay according to RGMII Version 2.0, with programming options for external delay and making adjustments and corrections to TX and RX timing paths
GMII/MII/RGMII with 3.3V/2.5V/1.8V tolerant I/Os
Auto-negotiation to automatically select the highest linkup speed (10/100/1000Mbps) and duplex (half/full)
On-chip termination resistors for the differential pairs
On-chip LDO controller to support single 3.3V supply operation – requires only one external FET to generate 1.2V for the core
Jumbo frame support up to 16KB
125MHz Reference Clock Output
Energy-detect power-down mode
KSZ9031Mxx feature GMII/MII standard interface with 3.3V/2.5V/1.8V tolerant I/Os
KSZ9031Rxx feature RGMII timing supports on-chip delay according to RGMII Version 2.0, with programming options for external delay and making adjustments and corrections to TX and RX timing paths
GMII/MII/RGMII with 3.3V/2.5V/1.8V tolerant I/Os
Auto-negotiation to automatically select the highest linkup speed (10/100/1000Mbps) and duplex (half/full)
On-chip termination resistors for the differential pairs
On-chip LDO controller to support single 3.3V supply operation – requires only one external FET to generate 1.2V for the core
Jumbo frame support up to 16KB
125MHz Reference Clock Output
Energy-detect power-down mode
Specifikationer
Attribute | Value |
|---|---|
| Standard Supported | 1000BASE-T, 100BASE-TX, 10BASE-T, IEEE 802.3 |
| Number of Channels per Chip | 1 |
| Typical Data Rate | 1000Mbit/s |
| Power Supply Type | Single |
| Typical Operating Supply Voltage | 3.3 V |
| Mounting Type | Surface Mount |
| Package Type | QFN |
| Pin Count | 48 |
| Dimensions | 7 x 7 x 0.8mm |
| Maximum Operating Temperature | +70 °C |
| Automotive Standard | AEC-Q100 |
| Minimum Operating Temperature | 0 °C |