Electromen OY DC Motor Controller, 10/35 V dc, 15 A, Potentiometer Function

Se alla Motor Controllers

Antal (1 enhet)*

1 575,70 kr

(exkl. moms)

1 969,62 kr

(inkl. moms)

Add to Basket
välj eller skriv kvantitet
I lager
  • 32 enhet(er) är redo att levereras
  • Plus 16 enhet(er) är redo att levereras från en annan plats
Behöver du mer? Ange den kvantitet du behöver och klicka på "Kontrollera leveransdatum"
Enheter
Per enhet
1 +1 575,70 kr

*vägledande pris

RS-artikelnummer:
773-6841
Tillv. art.nr:
EM-241A
Tillverkare / varumärke:
Electromen OY
Hitta liknande produkter genom att välja ett eller flera attribut.
Välj alla

Brand

Electromen OY

Product Type

DC Motor Controller

Control Function

Potentiometer

Supply Voltage

10/35 V dc

Output Voltage

12/24 V

Current Rating

15 A

Overall Length

45mm

Overall Width

80mm

Overall Depth

45 mm

Minimum Operating Temperature

-40°C

Maximum Operating Temperature

60°C

Standards/Approvals

No

COO (Country of Origin):
FI

Electromen - EM-241A DC MOTOR CONTROLLER 10-35 V DC, 15A


The EM-241A is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed.The drive has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops.Adjustable current limit protects motor against overcurrent and it can also be used as an end-stop.This device has also two settable speeds, which are useful in positioning applications.The control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down, there is also individual limit inputs for FW and BW directions

SPEED-2 input activates pre-set speed-2, but it can also be used as input for analogue speed control signal 0-5V

STOP input can be set to work as current limit setting

FAULT terminal has at the same time input and output function, the pin is normally high, but is pulled down in overheat and conditionally also in current trip situation

There are two selectable control modes, continuous and impulse. In continuous mode the motor runs as long as the control is active. In impulse mode a short command starts the motor, and only a new impulse will change the status

There are special settings start-kick and auto reverse and the card has selectable input logics for both control and limit inputs

For parameters setting there are 3 options: EM-236 interface unit, EM-268 with Menthol-Lite PC-program and EM-326 with Menthol-App application for smartphone

Features and Benefits


12-24Vdc, 10-15A continuous, 25-30A peak

Speed, direction, current limiting, soft start/stop and auto-reverse control

Limit switch inputs for end of travel

Compact and DIN rail mountable;Compact with high current output

Current limit

Zero current limit

Overvoltage brake

Speed setting

Flexible control inputs

Impulse / continuous mode

DIN rail mountable

* Continuous current output when ambient temp is <50°C

12-24Vdc version drive =

15A at 100% speed / 10A at 5-99% speed

Peak (5secs) 30A

EM-24xA DC-Motor Controller


The EM-241A/ EM-243A are full bridge DC-motor starters. It is designed to work with DC-motor in applications where some special functions are needed.

Starter has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops. Adjustable current limit protects motor against overcurrent and it can also be used as an end-stop. This device has also two settable speeds, which are useful in positioning applications.

The parameters are set with EM-236 interface unit. Operation of the controller and some of its functional values can also be monitored with EM-236 interface unit.

Small size

High current output

Current limit

Zero current limit

Speed setting

Flexible control inputs

Impulse / continuous mode

Rail base mountable

Digital parameter setting

relaterade länkar