Oscilloscope Probes

An oscilloscope is considered to be the most used instrument for electrical engineers who need to measure electrical characteristics of electronic devices but you also need at least one probe.Things to consider when choosing probes Ensure the probe's input connector matches the connector on your scope Choose a probe whose input resistance and capacitance match the input resistance and capacitance of your scope - matching is critical for guaranteeing proper signal transfer and signal accuracyThe best approach, for matching a probe with a scope, is to first choose a probe whose capacitance is within the range of your scope and then fine-tune the probe's capacitance by adjusting its compensation network using the probe's trimmer capacitor. The 1X probes are suitable for many low frequency applications. They typically offer the same input impedance of the oscilloscope which is normally 1 M Ohm. The most common type of probe with a built in attenuator gives an attenuation of ten, and it is known as a 10X oscilloscope probeTypes of probesPassive probes are the most commonly used probes for taking measurements. They are easy to use, relatively inexpensive, and fairly rugged. Available in the following configurations: 1´: no attenuation 10´: factor-of-10 attenuation 100´: factor-of-100 attenuation 1000´: factor-of-1000 attenuationAttenuation probes serve to multiply the voltage measurement range of the oscilloscope by using an internal resistor that, when used in conjunction with the input resistance of the scope, creates a voltage divider. Useful for the following reasons: It allows for the measurement of a signal that might exceed the limits of the oscilloscope. The attenuation circuitry results in higher resistance and lower capacitance, which is important for high-frequency measurements.Active probes contain active components, such as FETs or amplifiers. Commonly used for taking high-speed measurements (>500 MHz) or on high-impedance circuits. One limitation is their limited voltage range. Differential probes are popular for measuring high-frequency signals or signals of very low amplitude.A current probe measures the electrical current flowing through a conductor. Tips Always use an appropriate probe tip and/or probe tip adapter whenever possible Keep ground leads short

...
Read more Read less

Filter

Visar 1 - 20 av 206 produkter
Resultat per sida
Beskrivning Pris Probe Type Attenuation Bandwidth Maximum Common Mode Input Voltage Connector Type Model Number p Number of Probes Safety Category Level Safety Category Voltage Series Safety Category Rise Time
RS-artikelnummer 209-7860
Tillv. art.nrP6243
VarumärkeTektronix
24 411,00 kr
Each
Enheter
Active 1:10 1GHz - BNC P6243 - - - - - 350ps
RS-artikelnummer 733-6141
Tillv. art.nrN2790A
15 902,00 kr
Each
Enheter
Differential, High Voltage 1:50, 1:500 100MHz 1.4kV BNC N2790A - CAT II, CAT III 600 V, 1000 V N CAT II 1000 V, CAT III 600 V 3.5ns
RS-artikelnummer 796-6702
Tillv. art.nrP6015A
VarumärkeTektronix
23 278,00 kr
Each
Enheter
High Voltage 1:1000 75MHz 20kV - P6015A 1 - - - - 4ns
RS-artikelnummer 734-5029
Tillv. art.nrP5200A
VarumärkeTektronix
11 742,00 kr
Each
Enheter
Differential, High Voltage 1:50, 1:500 50MHz 1kV - P5200A - CAT II 1000V P52XXA CAT II 1000 V -
RS-artikelnummer 224-1225
Tillv. art.nrSI-9002
VarumärkeTestec
2 897,55 kr
Each
Enheter
Active, Differential 1:20, 1:200 25MHz 1kV - TT-SI 9002 - CAT III 1000 V ac, 1400 V ac/dc SI CAT III 1000 V ac, CAT III 1400 V 14ns
RS-artikelnummer 512-5019
Tillv. art.nrMTX1032-B
VarumärkeMetrix
4 577,31 kr
Each
Enheter
Differential 1:1, 1:10, 1:100 30MHz - BNC MTX 1032-B 4 CAT I, CAT II, CAT III 600V - CAT I, CAT II, CAT III 600 V 11.7ns
RS-artikelnummer 481-0823
Tillv. art.nrP2220
VarumärkeTektronix
1 483,20 kr
Each
Enheter
Passive 1:1, 1:10 200MHz - - P2220 - CAT II 150 V, 300 V TPS2000 CAT II 15 V, CAT II 300 V -
RS-artikelnummer 752-7357
Tillv. art.nrTHDP0200
VarumärkeTektronix
21 733,00 kr
Each
Enheter
Differential, High Voltage 1:50, 1:500 200MHz 1.5kV BNC THDP0200 - CAT II, CAT III 600 V, 1000 V THD CAT II 1000 V, CAT III 600 V 1.8ps
RS-artikelnummer 733-6145
Tillv. art.nrN2791A
6 629,00 kr
Each
Enheter
Differential 1:10, 1:100 25MHz 700V BNC N2791A - CAT II 1000V ac N CAT II 1000 V ac 14ns
RS-artikelnummer 734-5026
Tillv. art.nrP5205A
VarumärkeTektronix
17 201,00 kr
Each
Enheter
Differential, High Voltage 1:50, 1:500 100MHz 1kV - P5205A - CAT II 1000V P52XXA CAT II 1000 V -
RS-artikelnummer 863-3740
Tillv. art.nrZS4000
VarumärkeTeledyne LeCroy
46 241,65 kr
Each
Enheter
Active 1:10 4GHz 8V ProBus ZS4000 1 - - ZS - -
RS-artikelnummer 224-1219
Tillv. art.nr15101
VarumärkeTestec
3 327,31 kr
Each
Enheter
Active, Differential 1:10, 1:100 25MHz 700V BNC TT-SI 9001 - CAT III 1000 V ac, 1400 V ac/dc SI CAT III 1000 V ac, CAT III 1400 V 14ns
RS-artikelnummer 672-1700
Tillv. art.nrPK400-1
VarumärkeTeledyne LeCroy
2 835,00 kr
Each
Enheter
Gripper - - - - PK400-1 - - - - - -
RS-artikelnummer 712-1141
Tillv. art.nrP5122
VarumärkeTektronix
3 337,20 kr
Each
Enheter
High Voltage, Passive 1:100 200MHz - - P5122 - CAT II 600 V ac, 1000 V ac TPS2000 CAT II 1000 V ac, CAT II 600 V ac 2.2ns
RS-artikelnummer 898-6744
Tillv. art.nrTA041
VarumärkePico Technology
3 298,46 kr
Each
Enheter
Active, Differential 1:10, 1:100 25MHz 700V - - 2 CAT III ±700 V, 700 Vrms - CAT III ±700 V, 700 Vrms -
RS-artikelnummer 366-9141
Tillv. art.nrTT-HVP15 HF
VarumärkeTestec
2 300,00 kr
Each
Enheter
Passive 1:1000 50MHz 10kV BNC TT-HVP15 HF - CAT I - HVP - 7ns
RS-artikelnummer 702-7910
Tillv. art.nr11060A
308,00 kr
Each
Enheter
Surface Mount Device - - - - 11060A - - - - - -
RS-artikelnummer 781-0807
Tillv. art.nrTCP0030A
VarumärkeTektronix
44 908,00 kr
Each
Enheter
Current - 120MHz - BNC TCP0030A 1 CAT II 150 V, 300 V TCP CAT II 150 V, CAT II 300 V 2.92ns
RS-artikelnummer 781-0810
Tillv. art.nrTCP305A
VarumärkeTektronix
19 570,00 kr
Each
Enheter
Current - 50MHz - BNC TCP305A 1 CAT II 150 V, 300 V TCP300 CAT II 150 V, CAT II 300 V 7ns
RS-artikelnummer 734-5013
Tillv. art.nrP5100A
VarumärkeTektronix
5 665,00 kr
Each
Enheter
Passive 1:100 500MHz 1kV - P5100A - CAT II 1000V ac 5000 CAT II 1000 V ac 700ps
Related Products
The i30 may be used in conjunction with ...
Description:
The i30 may be used in conjunction with bench and portable oscilloscopes for accurate non-intrusive ac & dc current measurement.,Applications include: inverters, switch mode power supplies, industrial controllers, automotive leakage currents and other applications requiring accurate isolated current measurement. ...
For measurement of flux density and magnetic field ...
Description:
For measurement of flux density and magnetic field strength of DC,AC and peak magnetic fields in S.I c.g.s units, these two micropressor-controlled menu-driven instruments are the GM07 & GM08 series. Featuring graphical monochrome LCD display, probe polarity inidicator and operating ...
MDO3000 oscilloscopes are designed to meet users' needs ...
Description:
MDO3000 oscilloscopes are designed to meet users' needs and aspirations now and into the future. Each model is multi-functional with integrated basic spectrum analyzer, Wave Inspector Navigation, MSO, serial and parallel bus triggering and analysis, and digital voltmeter. Optional instrument ...
Tektronix MSO/DPO2000 accessories include: analysis modules embedded serial ...
Description:
Tektronix MSO/DPO2000 accessories include: analysis modules embedded serial triggering DPO2EMBD ( 575-614 ), computer serial triggering DPO2COMP ( 575-563 ) and automotive serial triggering DPO2AUTO ( 575-573 ); video out port DPO2CONN ( 575-579 ); soft carrying case ACD2000 ( ...