Crimp Tool Positioners, Turrets & Locators

Crimp Tool Positioners are parts of a Crimping tool designed to adapt the tool frame to a particular application. Available in a wide selection of sizes and shapes locators guarantee versatility of every crimping tool. The data plate on each positioner designates which contacts the positioner accommodates for its wire size and indicates selector position. The positioners are easy to remove and replace when different connector size is required.


How easy crimping tools and positioners, turrets and locators are to use?


They are very easy to use, insert the contact pin into the hole of the crimp tool, load the wire into the contact pin, make sure it’s fully seated then and squeeze until the cycle finishes then finally check that you have a secure crimp.


How do you maintain the product?


There is very little maintenance required for this tool, keep the indenter tips free of debris and dirt.


The Importance of a High-Quality Crimp


When a crimping tool is used on a terminal, two crimps take place at the same time. One is the electrical connection between the conductor and the terminal. The other is the insulation crimp which provides strain relief against vibration and tension.The electrical connection must be gas-tight without any voids between the wire strands and the terminal. If there are any voids present, then corrosion can occur causing resistance and excessive heat which damages the electrical connection. Using a good quality crimping tool will ensure that a full, gas-tight crimp is produced preventing future deterioration of the electrical connection and insulation breakage.


...
Read more Read less

Filter

Visar 1 - 20 av 159 produkter
Resultat per sida
Beskrivning Pris Type Series Number of Contacts Series Number
RS-artikelnummer 531-425
VarumärkeRS PRO
653,24 kr
Each
Enheter
Positioner QM/TNM 16 -
RS-artikelnummer 822-7755
Tillv. art.nr63819-0975
VarumärkeMolex
563,01 kr
Each
Enheter
Locator T9999 - 63819
RS-artikelnummer 822-7758
Tillv. art.nr63819-0075
VarumärkeMolex
563,01 kr
Each
Enheter
Locator T9999 - 63819
RS-artikelnummer 756-7345
Tillv. art.nr09990000531
VarumärkeHARTING
1 722,23 kr
Each
Enheter
Positioner D-sub - -
RS-artikelnummer 515-1096
Tillv. art.nrM22520/2-09
VarumärkeGlenair
2 448,41 kr
Each
Enheter
Positioner M22520/2-09 - -
RS-artikelnummer 822-7717
Tillv. art.nr63811-8775
VarumärkeMolex
543,86 kr
Each
Enheter
Locator T9999 - 63811
RS-artikelnummer 687-5762
Tillv. art.nr89853093A
VarumärkeSouriau
4 800,66 kr
Each
Enheter
Positioner MicroComp - -
RS-artikelnummer 343-2826
Tillv. art.nrTH592
VarumärkeGlenair
2 494,73 kr
Each
Enheter
Turret AF8 - -
RS-artikelnummer 876-2321
Tillv. art.nr58516-1
VarumärkeTE Connectivity
629,81 kr
Each
Enheter
Locator PRO-CRIMPER III - -
RS-artikelnummer 360-1713
Tillv. art.nrTH1A
VarumärkeGlenair
2 423,08 kr
Each
Enheter
Turret M22520/1-02 - -
RS-artikelnummer 314-8414
Tillv. art.nr86-5
895,75 kr
Each
Enheter
Positioner M22520/7-06 - -
RS-artikelnummer 876-2210
Tillv. art.nr525442-9
VarumärkeTE Connectivity
2 026,85 kr
Each
Enheter
Plug Gauge - - -
RS-artikelnummer 876-1980
Tillv. art.nr4-539785-8
VarumärkeTE Connectivity
570,46 kr
Each
Enheter
Locator CERTI-CRIMP II - -
RS-artikelnummer 864-6976
Tillv. art.nr679192-1
VarumärkeTE Connectivity
7 445,21 kr
Each
Enheter
Wire Crimper 626 - -
RS-artikelnummer 864-7017
Tillv. art.nr69082
VarumärkeTE Connectivity
95 568,81 kr
Each
Enheter
Crimping Head DYNA-CRIMP - -
RS-artikelnummer 173-9631
Tillv. art.nr63825-8175
VarumärkeMolex
610,37 kr
Each
Enheter
Locator 207128 - 63825
RS-artikelnummer 674-1707
Tillv. art.nr809-005
VarumärkeGlenair
2 018,06 kr
Each
Enheter
Positioner - - -
RS-artikelnummer 721-1434
Tillv. art.nr1208461
VarumärkePhoenix Contact
702,50 kr
Each
Enheter
Assembly Tool SAC BIT M8-D10 - -
RS-artikelnummer 864-7020
Tillv. art.nr217200-1
VarumärkeTE Connectivity
27 110,45 kr
Each
Enheter
Crimping Head 626 - -
RS-artikelnummer 864-3431
Tillv. art.nr354003-8
VarumärkeTE Connectivity
1 786,55 kr
Each
Enheter
Wire Crimper - - -
Related Products
Place the tool into the cavity from front ...
Description:
Place the tool into the cavity from front face of the insulator Push on the handleRemove the contact by pulling on it.
Crimp die suitable for crimping 0.25-0.75mm2 cables with ...
Description:
Crimp die suitable for crimping 0.25-0.75mm2 cables with 1mm CombiTac contacts. Used in conjunction with CT-M-CZ crimp pliers (179-2472).
Crimp die suitable for crimping 2.5-4mm2 cables with ...
Description:
Crimp die suitable for crimping 2.5-4mm2 cables with 3mm CombiTac contacts. Used in conjunction with CT-M-CZ crimp pliers (179-2472).
Molex T9999 PremiumGrade series of tools provides the ...
Description:
Molex T9999 PremiumGrade series of tools provides the user with various options of high quality tooling to ensure your application is covered. A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision ...