Asco Solenoid Valve G238A048T6A4, 2 port , NC, 110 V ac, 3/4in

  • RS-artikelnummer 488-734
  • Tillv. art.nr G238A048T6A4
  • Tillverkare / varumärke Asco
Datablad
Lagstiftning och ursprungsland
Ej tillämpbart
COO (Country of Origin): GB
Produktdetaljer

Two-way, WRAS, N/C Water Valves

Two-way, brass-bodied WRAS listed solenoid valves with anti-water hammer devices fitted as standard. They have a zero bar minimum operating pressure and are normally closed. The compact, lightweight unit may be mounted in any position (however, for optimum life, certain models will work best when the solenoid coil is mounted vertically and upright). Series 238 solenoid valves incorporate "G" (BSP Parallel) threaded ports, while Series 262 solenoid valves offer 15mm compression fitting connection ports. The moulded electrical spade connection is based on ISO 4400/EN 175301-803, form A specifications and a DIN 43650 connector is supplied as standard.

Standards

UK WFBS listed

Compact solenoid valves suitable for most gas and fluid handling applications. Where practical, valves are shown with a schematic diagram showing the (circuit) function. The diagram is laid out so that the left-hand side of the diagram describes the valves operation when the coil is energised. When the coil is de-energised, the spring (or servo-assist) return controls the valve and is described on the right-hand side of the diagram. The 3 / 2-way designation indicates a valve with three ports and two modes of operation. It is normal practice to refer to 2 / 2-way valves as two ways. The port designations A, B, P, P1, P2 and R are used on the schematic diagrams and are marked on the valve bodies. Valve bodies are marked for a specific circuit function but can often be used for other functions. Reference to the schematic diagrams and technical specifications indicates the appropriate connections and pressure capabilities when an alternative circuit function is required.

Specifikationer
Attribute Value
Supply Voltage 110 V ac
Number of Ports 2
Operation Pilot
Connection 3/4 in G Female
Connection Size 3/4in
Default Valve Position NC
Suitable Applications Water
Type 2/2
Orifice Diameter 19mm
Body Material Brass
Maximum Working Pressure 10 bar
Operating Temperature Range -20 → +75 °C
Minimum Operating Temperature -20°C
Maximum Operating Temperature +75°C
Connection Gender Female
Series 238
Flow Factor Kv 4.5m³/h
Thread Standard or Connection Type G
Tillfälligt slut i lager – restorder för leverans 2020-01-28
Pris (ex. moms) Each
2 159,76 kr
(exkl. moms)
2 699,70 kr
(inkl. moms)
Enheter
Per unit
1 +
2 159,76 kr
Related Products
The Type 5282 Burkert solenoid valve is specially ...
Description:
The Type 5282 Burkert solenoid valve is specially characterised by its design in which there is fluid separation by the inclusion of a diaphragm seal in the pilot valve. This enables the coil to remain protected from the effects of ...
Two-way, pilot operated solenoid valves for hot water/steam ...
Description:
Two-way, pilot operated solenoid valves for hot water/steam applications, normally closed with threaded port connection. Brass bodyCompact design to minimize heat radiation lossDIN plug connection Ranging from -20 to +184°CCan be mounted in any position.
Two-way, direct operated, EN161 approved solenoid valves for ...
Description:
Two-way, direct operated, EN161 approved solenoid valves for use on gas pilot and gas burner control, zero bar minimum operating pressure, normally closed, threaded port connection. Pressure not required for operationCompact & lightweightISO 4400 DIN connectionClass A, group 2 service ...
Parker 2-way solenoid valves are used in a ...
Description:
Parker 2-way solenoid valves are used in a wide variety of applications with or without pressure differential. Ideally suited for air, liquids and gases, these valves are available with a brass or stainless steel body. CompressorsWater dispensing & purificationCooling systemsMedical ...