STMicroelectronics L298N, Brushed Motor Driver IC, 46 V 4A 15-Pin, MULTIWATT V

Datablad
Lagstiftning och ursprungsland
RoHS-Försäkran
Produktdetaljer

L298 Dual Full Bridge Motor Driver

ST Microelectronics presents its L298 dual full bridge driver series. The L298 series from ST is an integrated high voltage, high current dual full bridge driver. These devices are specially designed to accept standard TTL logic and drive inductive loads in Relays, Solenoids, DC and Stepper Motors. Featured are two enable inputs that allow the L298 to be enabled or disabled independently of the input signals. The emitters of the lower transistors of each bridge are connected together, the corresponding external terminal can be used to connect an external sensing resistor. In addition, a supply input is provided so that the logic works at a lower voltage.

Features

  • Operating supply voltage up to 46 V

  • Total DC current of up to 4 A

  • Low saturation voltage

  • Over-temperature protection

  • Logical "0" input voltage up to 1.5 V (high noise immunity)

What are Motor Driver IC's?

Motor Driver ICs are current amplifiers and are an essential component of motor interfacing. The motor driver integrated circuit chip acts as the interface between a microprocessor or microcontroller, and a motor. As microprocessors tend to operate at lower currents, and motors at higher, motor driver ICs are needed to supply current to the motor as needed. The RS Components range of Motor Driver ICs includes models from leading brands, in various types and configurations to support your design needs.

Motor Controllers & Drivers, STMicroelectronics

Specifikationer
Attribute Value
Motor Type Brushed DC
Output Configuration Dual Full Bridge
Maximum IGBT Collector Current 4A
Maximum Collector Emitter Voltage 46 V
Mounting Type Through Hole
Package Type MULTIWATT V
Maximum Operating Supply Voltage 46 V
Pin Count 15
Minimum Operating Supply Voltage 4.8 V
Maximum Operating Temperature +130 °C
Length 19.6mm
Dimensions 19.6 x 5 x 10.7mm
Height 10.7mm
Minimum Operating Temperature -25 °C
Width 5mm
250 I lager för leverans inom 1 arbetsdagar
Pris (ex. moms) Each (In a Tube of 25)
41,571 kr
(exkl. moms)
51,964 kr
(inkl. moms)
Enheter
Per unit
Per Tube*
25 - 100
41,571 kr
1 039,275 kr
125 - 225
30,739 kr
768,475 kr
250 - 475
29,932 kr
748,30 kr
500 - 1225
29,163 kr
729,075 kr
1250 +
28,435 kr
710,875 kr
Related Products
High-side switches can safely drive high currents in ...
Description:
High-side switches can safely drive high currents in resistive, inductive and capacitive grounded loads. Designed to work in the harsh automotive environment they requires both robust, low on-resistance power switch and accurate analogue circuitry for diagnostic, protection and control functions. ...
From Microchip the MTD6508 device is a 3-phase ...
Description:
From Microchip the MTD6508 device is a 3-phase full-wave sensorless driver for brushless DC (BLDC) motors that features a 180° sinusoidal drive, high torque output and silent drive. The MTD6508 is designed to cover a wide range of motor characteristics ...
Designed for pulse-width-modulated (PWM) control of DC motors, ...
Description:
Designed for pulse-width-modulated (PWM) control of DC motors, the A5950 is capable of peak output currents up to ±3 A and operating voltages from 5.5V to 40 V. DC motors are controlled using standard PHASE and ENABLE signals to permit ...
The A5995 is designed to operate at voltages ...
Description:
The A5995 is designed to operate at voltages up to 40 V while driving two DC motors at currents up to 3.2 A. The A5995 includes a fixed off-time pulse-width modulation (PWM) regulator for current control. The DC motors are ...