Texas Instruments USB Adapter Board, USB-TO-GPIO

  • RS-artikelnummer 819-7562
  • Tillv. art.nr USB-TO-GPIO
  • Tillverkare / varumärke Texas Instruments
Datablad
Lagstiftning och ursprungsland
RoHS-Försäkran
Produktdetaljer

USB Interface Adapter Evaluation Module

Texas Instruments USB-TO-GPIO USB Interface Adapter Evaluation Module serves as an interface adapter or a bridge between a host PC (IBM™ compatible) and one or multiple slave devices via a standard type-A to mini-B USB cable. The communication between the USB interface adapter and the host PC is via USB, while the communication between the USB interface adapter and the slave device(s) is via an inter-integrated circuit (I²C), SMBus, PMBus and/or general-purpose inputs/outputs GPIOs. The bridge converts communication transactions between the USB and serial protocol.

Supports master mode I²C, SMBus or PMBus as well as GPIO.
Supports USB1.1 full speed at 12 Mbit/s. The USB interface adapter is recognized by the host as a generic human interface device (HID), so no proprietary USB or HID driver is needed. Therefore, the USB interface adapter can be treated as a USB plug-and-play device.
Selects different clock speeds (either 100 kHz or 400 kHz) for I²C, PMBus, or SMBus communications.
Configures different pullup resistors for clock, data and ALERT signals (including open-drain).
Supports flexible I²C read or write transactions (specify raw data, instead of device address, command, etc.) .
Includes .NET DLL for supporting Windows .NET GUIs using the adapter.
No Windows dependencies other than the Microsoft .NET Framework version 2.0

The IEEE 1149.1 standard test access port and boundary-scan architecture uses devices known by the JTAG acronym, from Joint Test Action Group, and is used for testing and debugging system ports and PCB assemblies. Most embedded systems employ JTAG ports to enable in-circuit debugging and firmware programming, in addition to boundary scan testing.

Specifikationer
Attribute Value
Kit Classification Development Kit
Det är tyvärr inte möjligt att visa lagerbehållning för närvarande. Uppdatera sidan och försök igen.
Pris (ex. moms) Each
1 360,54 kr
(exkl. moms)
1 700,68 kr
(inkl. moms)
Enheter
Per unit
1 - 1
1 360,54 kr
2 - 3
1 325,69 kr
4 +
1 292,50 kr
Nästa dag-leverans inte möjlig
Related Products
The MikroElektronika RS232 2 click board performs full ...
Description:
The MikroElektronika RS232 2 click board performs full RS232 to Universal Asynchronous Receiver-Transmitter (UART) signal conversion. The MIKROE-2897 click features an On-board Surface Mount Device (SMD) jumper that allows selection of power supply voltage between 3.3V and 5V. This click ...
USB PD 3.0 compliantUniversal input mains voltage range: ...
Description:
USB PD 3.0 compliantUniversal input mains voltage range: from 90 VAC to 264 VAC (frequency from 45 Hz to 65 Hz)Three fixed PDOs available: 5 V, 9 V, 15 V – 3 A continuous operationLoad power limited to 45 WMinimum ...
The ANT7-T-ST25DV04K antenna reference board is a ready-to-use ...
Description:
The ANT7-T-ST25DV04K antenna reference board is a ready-to-use PCB that features an ST25DV04K dual interface EEPROM connected to a 14 mm x 14 mm, 13.56 MHz etched RF double layer antenna on one side, and to an I2C bus on ...
The UMFT201XA is a development module that converts ...
Description:
The UMFT201XA is a development module that converts USB to I²C two-wire serial bus interfaceSmall PCB assembly module designed to fit a standard 7.62mm (0.3”) wide 16-pin DIP socketOn board USB "mini-B" socket allows the module to be connected to ...